Why Lit Signs Go Dark Early
A practical guide to 12V LED modules and power supplies, for sign makers and the businesses that hire them
A lit sign is one of the hardest-working things a business owns. It’s out there every night, in the heat, the humidity and the rain, telling people you’re open. When it starts going patchy, flickering or dark, customers notice long before the owner does.
At Streamline Systems, we supply LED sign modules and power supplies to the local signage industry, and we’ve helped clients refurbish signs that failed long before they should have. When we open those signs up, the cause is almost always one of three things:
- Low-quality LEDs that dim, change colour or die early
- Unbranded power supplies with no real rating behind the label
- Overloaded power supplies, run at or past their limit until they fail
None of these is visible when the sign is new. They all show up a few months later.
What’s inside the box: LED sign modules explained
Most backlit signs, from lightboxes to channel letters, are lit by small LED modules chained together on a single cable, a bit like tape light but sturdier and easier to space out across a large face. Each module is a small sealed unit with its own LEDs, and the whole chain runs from a 12V power supply.
The modules we stock are:
- 12V, 1.5W per module, 3 LEDs
- IP67 rated, sealed against dust and water
- White or red, same specification
- Packs of 100 for TT$750 VAT inclusive, about TT$7.50 per module
The IP67 rating matters more here than almost anywhere. Between our heat, humidity, salt air and rain, water finds its way into signs, and an unsealed module or connection is usually the first thing to go.
Why red LED sign modules behind red faces
A red acrylic face works by letting red light through and blocking the rest. Put white modules behind it and much of that light is wasted inside the box, so the sign can look dull or slightly pink. Red modules put their light right where the face lets it through, giving a deeper, richer red. If the face is red, use red modules.
A red face blocks most of the light from white modules. Red modules emit the colour the face lets through.

Spacing depends on depth with LED sign modules
Every LED module throws a cone of light. The further the face is from the modules, the more those cones spread and overlap, and the more evenly the face lights up. In a shallow box, the cones don’t have room to spread, so you see each module as a bright dot through the face, with darker gaps between them. That’s what’s called a hot spot, and it’s one of the most common faults in a finished sign.
So there’s no single correct spacing. It depends on the distance between the modules and the face. The shallower the box, the closer together the modules need to be, and the more modules the sign needs. A common rule of thumb is to space modules no further apart than the depth of the box, and closer still for thin lightboxes or light-coloured faces that show everything behind them.

In a shallow box, close the gap between modules. In a deep box, the light has room to spread.
This also changes the power supply sum. A shallow sign needs more modules, which means more watts, so size the supply after the layout is set, not before.
The power supply is where corners get cut
The power supply is the heart of the sign, and it’s the part most often chosen on price alone. An unbranded supply may carry a big wattage number on its label, but there’s no telling what it will really deliver, how hot it runs, or what happens when it fails.
We pair our modules with genuine Mean Well power supplies, and we keep two models in stock:
- Mean Well LPV-100-12: 12V, 102W, IP67 encapsulated, constant voltage, with short circuit, over-current and over-voltage protection. A good fit for smaller signs.
- Mean Well XLG-200-12: 12V, 192W, IP67 in a metal enclosure, rated for case temperatures from -40 to +90°C, with a 5-year Mean Well warranty. Our choice for larger signs and harsh outdoor locations.
The 80% rule
Even a good power supply fails early if it’s pushed to its limit. Running flat out makes it hot, and heat is what wears electronics down. The rule of thumb across the industry is to load a supply to no more than about 80% of its rating.
With 1.5W modules, the maths is simple:
- LPV-100-12: 102W × 80% ≈ 81W, or about 54 modules
- XLG-200-12: 192W × 80% ≈ 154W, or about 100 modules

One pack of 100 modules sits comfortably on an XLG-200-12. On a 150W supply, it runs flat out.
So a full pack of 100 modules (150W) pairs neatly with one XLG-200-12, running at about 78% of its rating. Hanging 100 modules on a 100W or 150W supply is how signs end up dark within a year.
For business owners: you’re paying for what you can’t see
When you compare sign quotes, the faces, letters and finishes are easy to judge. The modules and power supply hidden inside aren’t, and that’s where the cheap quote saves its money. A sign that fails early costs more than the repair: there’s the call-out, the time it sits dark, and the impression it gives everyone driving past.
| A sign is only as good as the parts you can’t see. The faces and letters are easy to judge. The modules and power supply inside are where a cheap quote saves its money. |
A good sign maker will be happy to tell you exactly what’s going inside your sign. Ask.
Five questions to ask before you build or buy
1 Is the power supply a genuine, branded unit, and is it IP rated for where it’s going?
2 Is it loaded to around 80% or less, not run flat out?
3 Are the modules IP67, and from a reliable supplier rather than the cheapest option?
4 Is the module spacing right for the box depth, so the face lights evenly without hot spots?
5 For red faces, are red modules being used?
Built to last, in stock locally
We try to keep both modules and Mean Well power supplies in stock, so sign makers aren’t left waiting weeks on a shipment with a job half built.
Shop LED modules and Mean Well power suppliesWe try to keep both modules and power supplies in stock, with delivery available. Whether you’re building signs, refurbishing one, or just want to know what should be inside yours, we’re happy to help. |




Leave a comment